SPC Performance

Add a little horsepower, use grippy tires, launch hard, and take a corner at 1.5 G's. You need an adjustable rear control arm to optimize your tire contact by adjusting your camber. Be confident your...

Use this adjustable lower ball joint to get back to specification on the Honda Civic, CR-V, and Accord. Whether you are tracking your vehicle or need some change to stop tire wear, this maintenance...

Use this adjustable ball joint to get back to specification on the Honda Civic, CR-V, and Accord. Whether you are tracking your vehicle or need some change to stop tire wear, this maintenance free...

Remove and replace your factory rear upper control arm with SPC's adjustable arm to make rear camber changes on your latemodel Honda. SPC's unique adjustment design permits on car adjustment of +-3...

Replace your worn or damaged factory lower ball joint on the front of the 10th generation Civic or late model CR-V with this replacement ball joint from SPC. This ball joint uses high quality...

A must for every alignment tech, this spec book lists all major alignment angles for all vehicles from 2013-2023. Front caster, camber and toe, rear camber and toe, along with SAI and turning angle...

Spread the load! "Z" blocks and other axle spacers used by Hendrickson, Freightliner, Kenworth, Mack, Hollis, Sterling, Ford and others create pressure points that will crush or even break the...

This 3 piece set includes: 3.0", 3.5", 4.0" - Often called "dimple dies", flared hole dies are used in sheet-metal fabrications to provide rigidity and strength to flat, unsupported panels. Due to...

Often called "dimple dies", flared hole dies are used in sheet-metal fabrications to provide rigidity and strength to flat, unsupported panels. Due to the resulting high strength -to-weight ratio...

Product appearance and features may vary in the market as design changes, improvements and modifications are implemented.Installation Instructions

Spread the load! "Z" blocks and other axle spacers used by Hendrickson, Freightliner, Kenworth, Mack, Hollis, Sterling, Ford and others create pressure points that will crush or even break the...

Often called "dimple dies", flared hole dies are used in sheet-metal fabrications to provide rigidity and strength to flat, unsupported panels. Due to the resulting high strength -to-weight ratio...

These 3-3/4" steel adjusting sleeves are the perfect fit with our pivot studs and ball joint plates. California Residents WARNINGInstallation Instructions

Product appearance and features may vary in the market as design changes, improvements and modifications are implemented.

3/8" Rotary File. ......CAUTION: Always wear safety glasses when using cutting or grinding tools and equipment. California Residents WARNING

This 3/8" rotary file is specifically designed for aluminum. Use it to quickly and cleanly expand cam slots in aluminum brakets and frames. It is an ideal tool to use when installing SPC Nissan and...

This rotary file set is ideal for every technician. Be ready to elongate slots in Aluminum and Steel frames and brackets to accept larger offset cams. The kit includes one 85127 rotary file for...

Product appearance and features may vary in the market as design changes, improvements and modifications are implemented.

Spread the load! "Z" blocks and other axle spacers used by Hendrickson, Freightliner, Kenworth, Mack, Hollis, Sterling, Ford and others create pressure points that will crush or even break the...

Product appearance and features may vary in the market as design changes, improvements and modifications are implemented.Installation Instructions

This is the highest strength and most versatile Ball Joint Removal Tool on the market. The unique design of the forged 4-Way Ball Joint Separator allows the tool to be adjusted to remove ball joints...

Often called "dimple dies", flared hole dies are used in sheet-metal fabrications to provide rigidity and strength to flat, unsupported panels. Due to the resulting high strength -to-weight ratio...

These 4" anodized aluminum adjusting sleeves are the perfect fit with our pivot studs and ball joint plates. California Residents WARNING

This 5 piece set includes: .75", 1.0", 1.5", 2.0", 2.5" - Often called "dimple dies", flared hole dies are used in sheet-metal fabrications to provide rigidity and strength to flat, unsupported...